Hi OpenHAB Forum, i tryed to install openhab2 with a KNX Binding (binding-knx1 - 1.9.0.SNAPSHOT) today. The Connection to my Weinzierl KNX IP BAOS 771 works find. 2016-12-29 03:09:53.835 [INFO ] [nx.internal.connection.KNXConnection] - Established connection to KNX bus on 192.168.5.4:3671 in mode …

one more thing: your group-adress in your item is: “2/0/20” But within ETS Group Monitor there is “Zieladresse” => “2/20” It seems that you use different settings for ETS and openHAB! Use main/middle/sub level (2/0/20 respectively) or main/sub levels (2/20 respectively). But it should be the sam…

Hi there, I have exactly the same problem here. I use a BleuComm 'Azur proServ IP Gateway. @DirkSander at least in my case there’s no problem with the line-couplers. If i remember correctly, there once was a problem in the knx binding related to messages sent back to the knx bus. Maybe the probl…

Hi MikeFo! Yes - that problem still exists. In my environment (OH2b5 with KNX1.9) all reading-actions will produce a GroupValueWrite to the knx-bus. That is a real problem if you do not deal with that. It could lead to traffic-flood and will tear down your knx-bus if you do not handle it and use a …

Hi all i think i have found my problem. the BOAS 771 Firmware has one (or more) Bugs. i made a small exmaple Project with ETS5 and i needed over 4 Houers for Programming one Interface! (with ETS4 less then 5 minutes) I found in knx-user-forum.de a post with this message: Nach Mailkontakt mit Wein…

I have the same issue. My installation has been working many months and was working fine until I moved to openhab-binding-knx1/1.9.0.b5 or 1.9.0.SNAPSHOT If I revert to 1.9.0.b4 it works fine again. Have been using the Gira IP Coupler all along. Regards Mark.

@crystollic I have read in one post the colimero backand was updated and i think since this time we have our problems. But i think openhab works nie in spec and our Gateway habe problems. In my case i need a Firmware Update . Btw Some day ago i read a Post in openhab with a Gira Interface an the…

So, i have a new Firmware on my BOAS 771 and installed a new clean openhab2 final but still the same Problem. I get a message from knx bus and Openhup sends something back… and with the new Installation i get some new Errors… 2017-02-12 22:33:26.423 [WARN ] [eclipse.jetty.servlet.ServletHandler] …

[image] schneider_mav: So, i have a new Firmware on my BOAS 771 and installed a new clean openhab2 final but still the same Problem.I get a message from knx bus and Openhup sends something back… Have you tried: ignorelocalevents=true in the `/etc/openhab2/services/knc.cfg ? The other jetty…

nobody now something about this Problem? is the configuration ok? is the bous 771 not supported?

openHAB Community

Value 'ON' could not be sent to the KNX bus

Add-ons Bindings

schneider_mav (Schneider) February 17, 2017, 8:03pm 17

Now it Looks good with this config:

ip=192.168.5.4
busaddr=1.1.202
ignorelocalevents=true
type=TUNNEL
readRetries = 0

and this KNX Version (1.9.0-201611251544)

OH2 repeated writes to KNX interface