---
layout: documentation
title: ZEN32 - ZWave
---

{% include base.html %}

# ZEN32 Scene Controller
This describes the Z-Wave device *ZEN32*, manufactured by *[Zooz](http://www.getzooz.com/)* with the thing type UID of ```zooz_zen32_00_000```.

The device is in the category of *Wall Switch*, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.

![ZEN32 product image](https://opensmarthouse.org/zwavedatabase/1364/image/)


The ZEN32 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers.  This device is also able to participate in the routing of data between other devices in the mesh network.

## Overview

**Features**

  * Switch button: 15 A relay for Z-Wave on/off control
  * 4 remote control buttons: trigger scenes and control other devices in your Z-Wave network from this switch
  * **NEW 700 series Z-Wave** chip for better range and faster control
  * **Direct 3-Way**: works with regular on/off switches in a 3-way
  * **Scene control**: trigger actions with multi-tap (select hubs only)
  * **Smart bulb mode**: disable relay and control the light via Z-Wave
  * Adjustable LED indicator in 4 colors and 3 brightness levels
  * S2 Security and SmartStart for easier inclusion

**Specifications**

  * Model Number: ZEN32
  * Z-Wave Signal Frequency: 908.42 MHz
  * Power: 120 VAC, 60 Hz
  * **Maximum Load**: 150W LED, 960W Incandescent, 1800W (15A) Resistive, 3A motor (DON'T use with receptacles)
  * Range: Up to 500 feet line of sight
  * Operating Temperature: 32-104°F (0-40°C)
  * Installation and Use: Indoor only

### Inclusion Information

  1. Start Z-Wave inclusion.
  2. Quickly press the switch button 3 times.

The LED indicator will blink blue to signal communications and turn green for 3 seconds if inclusion is successful or turn red for 3 seconds if the pairing attempt fails.

### Exclusion Information

  1. Start Z-Wave exclusion.
  2. Quickly press the switch button 3 times.

If successful, the LED will turn green for 3 seconds.

### General Usage Information

  * **SWITCH BUTTON**: on/off of connected load, reports association Group 1 lifeline to the controller, Group 2 basic set, Group 3 multilevel; reports Scene 5 with 7 attributes (actions)
  * **BUTTON 1**: Group 4 basic set, Group 5 multilevel; Scene 1 (7 actions)
  * **BUTTON 2**: Group 6 basic set, Group 7 multilevel; Scene 2 (7 actions)
  * **BUTTON 3**: Group 8 basic set, Group 9 multilevel; Scene 3 (7 actions)
  * **BUTTON 4**: Group 10 basic set, Group 11 multilevel; Scene 4 (7 actions)

If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the device to factory settings, press and hold the switch button for 20 seconds until the LED indicator starts flashing red. Release the button, and immediately after, tap remote button 1 once to complete the reset. The LED indicators on all buttons will flash red to confirm a successful reset. Note: all previously recorded activity and custom settings will be erased from the device's memory.

## Channels

The following table summarises the channels available for the ZEN32 -:

| Channel Name | Channel ID | Channel Type | Category | Item Type |
|--------------|------------|--------------|----------|-----------|
| Switch | switch_binary | switch_binary | Switch | Switch | 
| Scene Number | scene_number | scene_number |  | Number | 

### Switch
Switch the power on and off.

The ```switch_binary``` channel is of type ```switch_binary``` and supports the ```Switch``` item and is in the ```Switch``` category.

### Scene Number
Triggers when a scene button is pressed.

The ```scene_number``` channel is of type ```scene_number``` and supports the ```Number``` item.
This channel provides the scene, and the event as a decimal value in the form ```<scene>.<event>```. The scene number is set by the device, and the event is as follows -:

| Event ID | Event Description  |
|----------|--------------------|
| 0        | Single key press   |
| 1        | Key released       |
| 2        | Key held down      |
| 3        | Double keypress    |
| 4        | Tripple keypress   |
| 5        | 4 x keypress       |
| 6        | 5 x keypress       |



## Device Configuration

The following table provides a summary of the 21 configuration parameters available in the ZEN32.
Detailed information on each parameter can be found in the sections below.

| Param | Name  | Description |
|-------|-------|-------------|
| 1 | LED Indicator mode for relay | LED Indicator mode for relay |
| 2 | LED Indicator mode for Button 1 | LED Indicator mode for Button 1 |
| 3 | LED Indicator mode for Button 2 | LED Indicator mode for Button 2 |
| 4 | LED Indicator mode for Button 3 | LED Indicator mode for Button 3 |
| 5 | LED Indicator mode for Button 4 | LED Indicator mode for Button 4 |
| 6 | LED Indicator color for relay | LED Indicator color for relay |
| 7 | LED Indicator color for Button 1 | LED Indicator color for Button 1 |
| 8 | LED Indicator color for Button 2 | LED Indicator color for Button 2 |
| 9 | LED Indicator color for Button 3 | LED Indicator color for Button 3 |
| 10 | LED Indicator color for Button 4 | LED Indicator color for Button 4 |
| 11 | LED Indicator brightness for relay | LED Indicator brightness for relay |
| 12 | LED Indicator brightness for Button 1 | LED Indicator brightness for Button 1 |
| 13 | LED Indicator brightness for Button 2 | LED Indicator brightness for Button 2 |
| 14 | LED Indicator brightness for Button 3 | LED Indicator brightness for Button 3 |
| 15 | LED Indicator brightness for Button 4 | LED Indicator brightness for Button 4 |
| 16 | Auto Turn-Off Timer for Relay | Auto Turn-Off Timer for Relay |
| 17 | Auto Turn-On Timer for Relay | Auto Turn-On Timer for Relay |
| 18 | State After Power Failure | State After Power Failure |
| 19 | Disable / Enable Control on the Relay | Disable / Enable Control on the Relay |
| 20 | Relay Behavior with Disabled Local / Z-Wave Control | Relay Behavior with Disabled Local / Z-Wave Control |
| 21 | 3-Way Switch Type | 3-Way Switch Type |

### Parameter 1: LED Indicator mode for relay

LED Indicator mode for relay
Choose if you want the LED indicator to turn on when the relay is on or off, or if you want it to remain on or off at all times.
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | LED on when relay off, LED off when relay on (default) |
| 1 | LED on when relay on, LED off when relay off |
| 2 | LED always off |
| 3 | LED always on |

The manufacturer defined default value is ```0``` (LED on when relay off, LED off when relay on (default) ).

This parameter has the configuration ID ```config_1_1``` and is of type ```INTEGER```.


### Parameter 2: LED Indicator mode for Button 1

LED Indicator mode for Button 1
Choose if you want the LED indicator to turn on when Button 1 is on or off, or if you want it to remain on or off at all times.
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | LED on when dimmer off, LED off when dimmer on (default) |
| 1 | LED on when dimmer on, LED off when dimmer off |
| 2 | LED always off |
| 3 | LED always on |

The manufacturer defined default value is ```0``` (LED on when dimmer off, LED off when dimmer on (default)).

This parameter has the configuration ID ```config_2_1``` and is of type ```INTEGER```.


### Parameter 3: LED Indicator mode for Button 2

LED Indicator mode for Button 2
Choose if you want the LED indicator to turn on when Button 2 is on or off, or if you want it to remain on or off at all times.
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | LED on when dimmer off, LED off when dimmer on (default) |
| 1 | LED on when dimmer on, LED off when dimmer off |
| 2 | LED always off |
| 3 | LED always on |

The manufacturer defined default value is ```0``` (LED on when dimmer off, LED off when dimmer on (default)).

This parameter has the configuration ID ```config_3_1``` and is of type ```INTEGER```.


### Parameter 4: LED Indicator mode for Button 3

LED Indicator mode for Button 3
Choose if you want the LED indicator to turn on when Button 3 is on or off, or if you want it to remain on or off at all times.
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | LED on when dimmer off, LED off when dimmer on (default) |
| 1 | LED on when dimmer on, LED off when dimmer off |
| 2 | LED always off |
| 3 | LED always on |

The manufacturer defined default value is ```0``` (LED on when dimmer off, LED off when dimmer on (default)).

This parameter has the configuration ID ```config_4_1``` and is of type ```INTEGER```.


### Parameter 5: LED Indicator mode for Button 4

LED Indicator mode for Button 4
Choose if you want the LED indicator to turn on when Button 4 is on or off, or if you want it to remain on or off at all times.
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | LED on when dimmer off, LED off when dimmer on (default) |
| 1 | LED on when dimmer on, LED off when dimmer off |
| 2 | LED always off |
| 3 | LED always on |

The manufacturer defined default value is ```0``` (LED on when dimmer off, LED off when dimmer on (default)).

This parameter has the configuration ID ```config_5_1``` and is of type ```INTEGER```.


### Parameter 6: LED Indicator color for relay

LED Indicator color for relay
Choose the **color** of the LED indicator for the relay.

0 – white (default); 1 – blue; 2 – green; 3 – red
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | white (default) |
| 1 | blue |
| 2 | green |
| 3 | red |

The manufacturer defined default value is ```0``` (white (default)).

This parameter has the configuration ID ```config_6_1``` and is of type ```INTEGER```.


### Parameter 7: LED Indicator color for Button 1

LED Indicator color for Button 1
Choose the **color** of the LED indicator for Button 1.

0 – white (default); 1 – blue; 2 – green; 3 – red
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | white (default) |
| 1 | blue |
| 2 | green |
| 3 | red |

The manufacturer defined default value is ```0``` (white (default)).

This parameter has the configuration ID ```config_7_1``` and is of type ```INTEGER```.


### Parameter 8: LED Indicator color for Button 2

LED Indicator color for Button 2
Choose the color of the LED indicator for Button 2.
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | white (default) |
| 1 | blue |
| 2 | green |
| 3 | red |

The manufacturer defined default value is ```0``` (white (default)).

This parameter has the configuration ID ```config_8_1``` and is of type ```INTEGER```.


### Parameter 9: LED Indicator color for Button 3

LED Indicator color for Button 3
Choose the **color** of the LED indicator for Button 3.

0 – white (default); 1 – blue; 2 – green; 3 – red
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | white (default) |
| 1 | blue |
| 2 | green |
| 3 | red |

The manufacturer defined default value is ```0``` (white (default)).

This parameter has the configuration ID ```config_9_1``` and is of type ```INTEGER```.


### Parameter 10: LED Indicator color for Button 4

LED Indicator color for Button 4
Choose the **color** of the LED indicator for Button 4.

0 – white (default); 1 – blue; 2 – green; 3 – red
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | white (default) |
| 1 | blue |
| 2 | green |
| 3 | red |

The manufacturer defined default value is ```0``` (white (default)).

This parameter has the configuration ID ```config_10_1``` and is of type ```INTEGER```.


### Parameter 11: LED Indicator brightness for relay

LED Indicator brightness for relay
Choose the LED indicator's brightness level for the relay.
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | bright (100%) |
| 1 | medium (60%) (default) |
| 2 | low (30%) |

The manufacturer defined default value is ```1``` (medium (60%) (default)).

This parameter has the configuration ID ```config_11_1``` and is of type ```INTEGER```.


### Parameter 12: LED Indicator brightness for Button 1

LED Indicator brightness for Button 1
Choose the LED indicator's brightness level for Button 1.
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | bright (100%) |
| 1 | medium (60%) (default) |
| 2 | low (30%) |

The manufacturer defined default value is ```1``` (medium (60%) (default)).

This parameter has the configuration ID ```config_12_1``` and is of type ```INTEGER```.


### Parameter 13: LED Indicator brightness for Button 2

LED Indicator brightness for Button 2
Choose the LED indicator's brightness level for Button 2.
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | bright (100%) |
| 1 | medium (60%) (default) |
| 2 | low (30%) |

The manufacturer defined default value is ```1``` (medium (60%) (default)).

This parameter has the configuration ID ```config_13_1``` and is of type ```INTEGER```.


### Parameter 14: LED Indicator brightness for Button 3

LED Indicator brightness for Button 3
Choose the LED indicator's brightness level for Button 3.
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | bright (100%) |
| 1 | medium (60%) (default) |
| 2 | low (30%) |

The manufacturer defined default value is ```1``` (medium (60%) (default)).

This parameter has the configuration ID ```config_14_1``` and is of type ```INTEGER```.


### Parameter 15: LED Indicator brightness for Button 4

LED Indicator brightness for Button 4
Choose the LED indicator's brightness level for Button 4.
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | bright (100%) |
| 1 | medium (60%) (default) |
| 2 | low (30%) |

The manufacturer defined default value is ```1``` (medium (60%) (default)).

This parameter has the configuration ID ```config_15_1``` and is of type ```INTEGER```.


### Parameter 16: Auto Turn-Off Timer for Relay

Auto Turn-Off Timer for Relay
Use this parameter to enable or disable the auto turn-off timer function (the time after which you want the switch to automatically turn off once it has been turned on).

0 – disabled (default); 1 – 65535 (minutes)
Values in the range 0 to 65535 may be set.

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_16_4``` and is of type ```INTEGER```.


### Parameter 17: Auto Turn-On Timer for Relay

Auto Turn-On Timer for Relay
Use this parameter to enable or disable the auto turn-on timer function (the time after which you want the switch to automatically turn on once it has been turned off).

0 – disabled (default); 1 – 65535 (minutes)
Values in the range 0 to 65535 may be set.

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_17_4``` and is of type ```INTEGER```.


### Parameter 18: State After Power Failure

State After Power Failure
Set the on off status for the switch after power failure.
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Relay and buttons remember and restore last state (default) |
| 1 | Relay and buttons forced to off after power failure |
| 2 | Relay and buttons forced to on after power failure |

The manufacturer defined default value is ```0``` (Relay and buttons remember and restore last state (default)).

This parameter has the configuration ID ```config_18_1``` and is of type ```INTEGER```.


### Parameter 19: Disable / Enable Control on the Relay

Disable / Enable Control on the Relay
Enable or disable paddle on/off control (aka disable the relay). If disabled, you’ll only be able to control the connected light via Z-Wave. Scenes and other functionality will still be available through buttons.

**Values**: 0 – Disable local / physical control (from the button), enable Z-Wave control; 1 – Enable local / physical control (from the button), enable Z-Wave control (default); 2 – Disable local / physical control (from the button), disable Z-Wave control
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable local control, enable Z-Wave control |
| 1 | Enable local control, enable Z-Wave control (default) |
| 2 | Disable local control, disable Z-Wave control |

The manufacturer defined default value is ```0``` (Disable local control, enable Z-Wave control).

This parameter has the configuration ID ```config_19_1``` and is of type ```INTEGER```.


### Parameter 20: Relay Behavior with Disabled Local / Z-Wave Control

Relay Behavior with Disabled Local / Z-Wave Control
Set reporting behavior for disabled physical control.

**Values**: 0 – report on/off status when button is pressed and change LED indicator status if Parameter 19 is set to value 0 or 2; 1 – DON’T report on/off status when button is pressed and DON’T change LED indicator status if Parameter 19 is set to value 0 or 2 (but the relay will always send central scene command) (default)
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | report on/off status |
| 1 | DON'T report on/off status (default) |

The manufacturer defined default value is ```1``` (DON'T report on/off status (default)).

This parameter has the configuration ID ```config_20_1``` and is of type ```INTEGER```.


### Parameter 21: 3-Way Switch Type

3-Way Switch Type
Choose the type of 3-way switch you want to use with this switch in a 3-way set-up.

**Values**: 0 – regular mechanical 3-way on/off switch, use the connected 3-way switch to turn the light on or off (default); 1 – momentary switch, click once to change status (light on or off)
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | regular mechanical 3-way on/off switch (default) |
| 1 | momentary switch |

The manufacturer defined default value is ```0``` (regular mechanical 3-way on/off switch (default)).

This parameter has the configuration ID ```config_21_1``` and is of type ```INTEGER```.


## Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The ZEN32 supports 11 association groups.

### Group 1: Lifeline

The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation.
Lifeline
Main button binary switch (Z-Wave) / basic set (button) lifeline to hub

Association group 1 supports 1 node.

### Group 2: Basic Set (relay)

Basic Set
Main relay button basic set (pressed only, doesn’t send anything when switch turned on via hub)

Association group 2 supports 5 nodes.

### Group 3: Multilevel (relay)

Multilevel
Main relay button multilevel (held)

Association group 3 supports 5 nodes.

### Group 4: Basic Set (#1)

Basic Set
Small button #1 basic set (pressed)

Association group 4 supports 5 nodes.

### Group 5: Multilevel (#1)

Multilevel
Small button #1 multilevel (held) > in sequence > held = increase brightness, release = stop level, held = decrease brightness, release = stop level

Association group 5 supports 5 nodes.

### Group 6: Basic Set (#2)

Basic Set
Small button #2 basic set (pressed)

Association group 6 supports 5 nodes.

### Group 7: Multilevel (#2)

Multilevel
Small button #2 multilevel (held) > in sequence > held = increase brightness, release = stop level, held = decrease brightness, release = stop level

Association group 7 supports 5 nodes.

### Group 8: Basic Set (#3)

Basic Set
Small button #3 basic set (pressed)

Association group 8 supports 5 nodes.

### Group 9: Multilevel (#3)

Multilevel
Small button #3 multilevel (held) > in sequence > held = increase brightness, release = stop level, held = decrease brightness, release = stop level

Association group 9 supports 5 nodes.

### Group 10: Basic Set (#4)

Basic Set
Small button #4 basic set (pressed)

Association group 10 supports 5 nodes.

### Group 11: Multilevel (#4)

Multilevel
Small button #4 multilevel (held) > in sequence > held = increase brightness, release = stop level, held = decrease brightness, release = stop level

Association group 11 supports 5 nodes.

## Technical Information

### Endpoints

#### Endpoint 0

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_NO_OPERATION_V1| |
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SWITCH_BINARY_V1| |
| COMMAND_CLASS_TRANSPORT_SERVICE_V1| |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1| |
| COMMAND_CLASS_CENTRAL_SCENE_V3| |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1| |
| COMMAND_CLASS_SUPERVISION_V1| |
| COMMAND_CLASS_CONFIGURATION_V1| |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| |
| COMMAND_CLASS_POWERLEVEL_V1| |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1| |
| COMMAND_CLASS_ASSOCIATION_V2| |
| COMMAND_CLASS_VERSION_V2| |
| COMMAND_CLASS_INDICATOR_V3| |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3| |
| COMMAND_CLASS_SECURITY_2_V1| |

### Documentation Links

* [manual](https://opensmarthouse.org/zwavedatabase/1364/reference/zooz-z-wave-plus-scene-control-switch-zen32-online-manual.pdf)

---

Did you spot an error in the above definition or want to improve the content?
You can [contribute to the database here](https://opensmarthouse.org/zwavedatabase/1364).