I have configured this things:
Thing gpio:pigpio-remote:GPIO-pi-1 “GPIO-Pi 1” [host=“172.31.85.15”, port=8888] {
Channels:
// Heizung
Type pigpio-digital-output : GPIO-output-27 [ gpioId=27, invert=true]
// Pool Pumpe
Type pigpio-digital-output : GPIO-output-17 [ gpioId=17, invert=true]
// Jalousieen
Type pigpio-digital-output : GPIO-output-23 [ gpioId=23]
Type pigpio-digital-output : GPIO-output-24 [ gpioId=24]
Type pigpio-digital-output : GPIO-output-15 [ gpioId=15]
Type pigpio-digital-output : GPIO-output-14 [ gpioId=14]
Type pigpio-digital-output : GPIO-output-08 [ gpioId=08]
Type pigpio-digital-output : GPIO-output-07 [ gpioId=07]
Type pigpio-digital-output : GPIO-output-09 [ gpioId=09]
Type pigpio-digital-output : GPIO-output-13 [ gpioId=13]
Type pigpio-digital-output : GPIO-output-10 [ gpioId=10]
Type pigpio-digital-output : GPIO-output-22 [ gpioId=22]
Type pigpio-digital-output : GPIO-output-02 [ gpioId=02]
Type pigpio-digital-output : GPIO-output-03 [ gpioId=03]
}
I use this item config:
//Kellerfenster
Switch GpioOutput02 {channel=“gpio:pigpio-remote:GPIO-pi-1:GPIO-output-02”}
Switch GpioOutput03 {channel=“gpio:pigpio-remote:GPIO-pi-1:GPIO-output-03”}
//Küche
Switch GpioOutput07 {channel=“gpio:pigpio-remote:GPIO-pi-1:GPIO-output-07”}
Switch GpioOutput08 {channel=“gpio:pigpio-remote:GPIO-pi-1:GPIO-output-08”}
//Alex Fenster
Switch GpioOutput09 {channel=“gpio:pigpio-remote:GPIO-pi-1:GPIO-output-09”}
Switch GpioOutput13 {channel=“gpio:pigpio-remote:GPIO-pi-1:GPIO-output-13”}
//Alex Tür
Switch GpioOutput10 {channel=“gpio:pigpio-remote:GPIO-pi-1:GPIO-output-10”}
Switch GpioOutput22 {channel=“gpio:pigpio-remote:GPIO-pi-1:GPIO-output-22”}
//WZ West
Switch GpioOutput14 {channel=“gpio:pigpio-remote:GPIO-pi-1:GPIO-output-14”}
Switch GpioOutput15 {channel=“gpio:pigpio-remote:GPIO-pi-1:GPIO-output-15”}
//Pool Pumpe
Switch GpioOutput17 {channel=“gpio:pigpio-remote:GPIO-pi-1:GPIO-output-17”}
//Heizung
Switch GpioOutput27 {channel=“gpio:pigpio-remote:GPIO-pi-1:GPIO-output-27”}
// WZ Süd
Switch GpioOutput23 {channel=“gpio:pigpio-remote:GPIO-pi-1:GPIO-output-23”}
Switch GpioOutput24 {channel=“gpio:pigpio-remote:GPIO-pi-1:GPIO-output-24”}
and this startup rule:
rule “System startup initialization”
when System started
then
sendCommand(GpioOutput17, OFF)
sendCommand(GpioOutput27, OFF)
sendCommand(GpioOutput23, ON)
sendCommand(GpioOutput02, ON)
sendCommand(GpioOutput03, ON)
sendCommand(GpioOutput07, ON)
sendCommand(GpioOutput08, ON)
sendCommand(GpioOutput09, ON)
sendCommand(GpioOutput10, ON)
sendCommand(GpioOutput13, ON)
sendCommand(GpioOutput14, ON)
sendCommand(GpioOutput15, ON)
sendCommand(GpioOutput22, ON)
sendCommand(GpioOutput23, ON)
sendCommand(GpioOutput24, ON)
end
This configuration worked fine before I go to release 3.1
I used 3.1.0.M4 - Milestone Build.
Now I make this test:
I start openhab without this gpio thing configuration, now the gpio’s not in use.
Then I create the thing configuration and save it, now the gpio’s switched on and hold the on state. The relais switched on.
This is an new situation. The milstone builds only activate the gpio’s with the thing configuration but doesnt switch them.
I hope you can understand my problem.
Thanks
Best regards
Walter