I’ve removed the map for this post - but this works as well … I like this solution, as it enables interactive grafana charts (local and remote) in a very easy way (once the SSL stuff is setup …).
Just in case someone else used this feature in 4.0.
I think i found why: checked permissions on synology docker folder and change to full access for the some users. Restart container and the “remove bindings” are back.as in previous versions…
Thanks,
Patrick
Hi,
first of all Merry Christmas and congratulations to the new release.
Of course I had to update it right away and it went smoothly.
The only thing i discovered is that since the upgrade to 4.1 I have a high CPU consumption of my docker container (openhab/openhab:latest-alpine):
Does anybody else have such high CPU usage?
Anyone has an idea where this curl commands come from? How can I find the origin of this never ending curls?
Best regards,
Patrick
UPDATE: After switching to latest-debian image the CPU utilization is back to normal.
Hi @patrick023
exactly the same behavior on my site with docker with high cpu, but no curl. MyThread
The threads which causing it are known but possible solution not yet available. I hope that someone can give us a hint how to really deactivate the “suggestionfinder”
I don’t agree with your assessement that about the suggestion finders being the cause. Jmdns has always been running in previous versions as well. Disabling the suggestion finder will stop the suggestion finder from running and create a dependency on it. You will not see mdns based suggestions.
It is different for UPnP as it is not running by default without an add-on that uses it. That should be completely stopped when disabling the suggestion finder.
The real issue seems to be that jmdns tries to scan on all network interfaces. That is independent of the suggestion finder. I don’t know if anything changed there.
I upgrade from 4.0.4 to 4.1 and all is good except I have a roller shutter blind widget and the stop command has been stripped out of the thing channel.
I can put it back in easily enough but it is strange how it has been removed.
Here is the code in the thing channel under the advanced settings after the upgrade:
UID: mqtt:topic:mqttbroker:0cb7d742b7
label: Blinds 1 - 7
thingTypeUID: mqtt:topic
configuration: {}
bridgeUID: mqtt:broker:mqttbroker
location: Lounge
channels:
- id: blind1control
channelTypeUID: mqtt:rollershutter
label: Blind 1 control
description: ""
configuration:
commandTopic: zigbee2mqtt/blind1/set
stateTopic: zigbee2mqtt/blind1
transformationPattern: JSONPATH:$.position
off: CLOSE
on: OPEN
Here is the same part after I put the STOP back in.
UID: mqtt:topic:mqttbroker:0cb7d742b7
label: Blinds 1 - 7
thingTypeUID: mqtt:topic
configuration: {}
bridgeUID: mqtt:broker:mqttbroker
location: Lounge
channels:
- id: blind1control
channelTypeUID: mqtt:rollershutter
label: Blind 1 control
description: ""
configuration:
commandTopic: zigbee2mqtt/blind1/set
stop: STOP
stateTopic: zigbee2mqtt/blind1
transformationPattern: JSONPATH:$.position
off: CLOSE
on: OPEN
The other strange part is the word STOP is in the place where the stop command is entered but if I clear it using the x on the right hand side of the field it just comes back again but doen’t update the code.
I have now tried to run update.bat 4.1.0 but update fails when backup is being created and upgrading fails. I have also tried to delete the backup part in update.ps1 file but still the backup is being made. Any ideas?
For a number of bindings I have newly installed in 4.1.0 from Community Marketplace and Other Add-ons, the Settings icon does not appear on the binding’s page.
The bindings are listed on the Settings page under Add-on Settings, but when I click on them, the settings page for the binding appears and is blank.
I’ve tried this with a selection of bindings and almost all I have tried have inaccessible settings. For example, HABSpeaker works and I can access the settings, but Signal does not.
What settings do you expect for the Signal binding? Changing the logging is only available for distribution add-ons (and JSON 3rd party if the developer provides that information). It is not available for other add-ons.
Thanks for the clarification, bindings with no settings obviously won’t have a Settings icon on their page. This is clearly correct behaviour.
My confusion has arisen because bindings with no settings are listed under “Add-on Settings” on the Settings page and display a blank page when you click on them.